Call Today

 

How do you feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bathtub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily obtainable, the task can relocate easily; if you need to open up a wall surface to eliminate the old tub and place the new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have certified on your own for the work as well as are comfortable trying it. Rather than working with a service provider to take control of a halfway-completed job, it is better to think about using one prior to you start. Chances are you may need an expert plumber to make tube connections.
This write-up will certainly assist you mount a new bath tub in your restroom if you have already purchased a brand-new tub as well as don't need to change the setup of your previous water pipes.
Your devices as well as product checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Preparing for the Setup

Firstly, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its final position.

 

 

Removing Old Touches

If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The process of eliminating the existing faucets can be fairly troublesome due to the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bathtub

Using the two wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub until the level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the water system and check all joints and new pipework for leakages and tighten them if necessary. Fill the tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait until the bathtub has actually been utilized at least once as this will settle it right into its final placement.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type must be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bathtub

In the area where the bath fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture and possible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof sticky and grout.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I recently found that blog entry about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the internet. Sharing is caring. One never knows, you may just be helping someone out. Bless you for your time. Don't forget to visit our site back soon.

Need expertise? Dial.